Sunday, 10 February 2019
EIGRP Routing With Redistribution
EIGRP (Enhanced Interface Gateway Routing Protocol)
For same Autonomous no. -->eigrp-routing.html
Redistribution
with different Autonomous No.
1.
It is used for 2 different autonomous system
2.
Redistribution depend of 5 component
1.Bandwith
2.Dely
3.Load
4.Reliablity
5.MTU (Max. transmission unit)
Step 3 Redistribution
Go to that router in which two or more autonomous no. are present (router 2)
and redistribute
for example
In these condition go to router 2 and follow the step's
Basic Configuration And Clock Rate
First router(2621-XM) and add port(WIC-2T) and Follow this Diagram
No
Router>en
Router#conf t
Router(config)#int s0/0
Router(config-if)#ip address 192.168.30.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#clock rate 64000
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Go to second router in cli mode
No
Router>en
Router#conf t
Router(config)#int s0/0
Router(config-if)#ip address 192.168.30.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int s0/1
Router(config-if)#ip address 192.168.40.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#clock rate 64000
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ip address 192.168.20.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Go to Third router in cli mode
No
Router>en
Router#conf t
Router(config)#int s0/0
Router(config-if)#ip address 192.168.40.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ip address 192.168.50.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Step 2 Routing
In First Router
In First Router
First check network in (Router# Show ip route)
Then type
Router#conf t
Router(config)#router eigrp 10
Router(config-router)#network 192.168.10.0
Router(config-router)#network 192.168.30.0
In Second router
Router# Show ip route
Router#conf t
Router(config)#router eigrp 10
Router(config-router)#network 192.168.20.0
Router(config-router)#network 192.168.30.0
Router(config)#router eigrp 20
Router(config-router)#network 192.168.40.0
Router(config-router)#network 192.168.20.0
In Third router
Router# Show ip route
Router#conf t
Router(config)#router eigrp 20
Router(config-router)#network 192.168.40.0
Router(config-router)#network 192.168.50.0Go to that router in which two or more autonomous no. are present (router 2)
and redistribute
for example
In these condition go to router 2 and follow the step's
Go to first AS
Router(config)#Router eigrp 10
Router(config-router)#Redistribute eigrp 20 metric 1544 2000 255 1 1500
Router(config-router)#Exit
Go to Second AS
Router(config)#Router eigrp 20
Router(config-router)#Redistribute eigrp 10 metric 1544 2000 255 1 1500
Where:-
1544 - Bandwith
2000 - Dely
255 - load
1 - Reliability
1500 - MTU
To check Send Packet's Between Networks or ping from fist router to all ip's as shown in picture
Subscribe to:
Post Comments
(
Atom
)
No comments :
Post a Comment