Computer And Technology

In these blog you will get information about how to make bootable pendrive, N+ , data sharing, cmd related function and other types of courses and technology

Sunday, 10 February 2019

EIGRP Routing

Million Things 03:40 No comments :
EIGRP (Enhanced Interface Gateway Routing Protocol)

1.   It is Dynamic Routing Protocol
      2.   It is also known as hybrid Protocol combine and Border Gateway Protocol
      3.   EIGRP is classless Routing protocol and support CIDR network
      4.   EIGRP use Autonomous no. system (as) range 1 to 65535
     5.   Autonomous no. must same between two router
           EIGRP support 255 networks 

Now Configure EIGRP Dynamic Routing

       Basic Configuration And Clock Rate
First router(2621-XM) and add port(WIC-2T) and Follow this Diagram


Go to first router in cli mode and type
          No
          Router>en
          Router#conf t
          Router(config)#int s0/0
          Router(config-if)#ip address 192.168.30.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#clock rate 64000
          Router(config-if)#exit
          Router(config)#int f0/0
   Router(config-if)#ip address 192.168.10.1 255.255.255.0
   Router(config-if)#no shut
          Router(config-if)#exit

Go to second router in cli mode
          No
          Router>en
          Router#conf t
          Router(config)#int s0/0
          Router(config-if)#ip address 192.168.30.2 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
          Router(config)#int s0/1
          Router(config-if)#ip address 192.168.40.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#clock rate 64000
          Router(config-if)#exit
          Router(config)#int f0/0
          Router(config-if)#ip address 192.168.20.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit


Go to Third router in cli mode
          No
    Router>en
          Router#conf t
    Router(config)#int s0/0
          Router(config-if)#ip address 192.168.40.2 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
          Router(config)#int f0/0
          Router(config-if)#ip address 192.168.50.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit

Step 2 Routing  

In First Router
First check network in (Router# Show ip route)
Then type
Router#conf t
Router(config)#router eigrp 10
Router(config-router)#network 192.168.10.0
Router(config-router)#network 192.168.30.0

In Second router
Router# Show ip route
Router#conf t
Router(config)#router eigrp 10
Router(config-router)#network 192.168.20.0
Router(config-router)#network 192.168.30.0
Router(config-router)#network 192.168.40.0

In Third router
Router# Show ip route
Router#conf t
Router(config)#router eigrp 10
Router(config-router)#network 192.168.40.0
Router(config-router)#network 192.168.50.0


To check Send Packet's Between Networks or ping from fist router to all ip's as shown in picture

                                        --------------------------END-----------------------



FOR DIFFERENT AS CLICK ON --> EIGRP ROUTING

No comments :

Post a Comment

Subscribe to: Post Comments ( Atom )

Contact Form

Name

Email *

Message *