Computer And Technology

In these blog you will get information about how to make bootable pendrive, N+ , data sharing, cmd related function and other types of courses and technology

Saturday, 9 February 2019

Million Things 04:02 No comments :

   Routing By RIP-V2 

   RIP-V2 (Routing information Protocol Version 2)
       1.   It is RIP second form
       2.   RIP-V2 is also Dynamic routing protocol
       3.   RIP-V2 is classless routing protocol
       4.   RIP-V2 is Max. Support is 15 network

Different Between RIP and RIPV2
   RIP support classful network only
   RIP-V2 Support both classful and classless network 
   Classful network does not use subnetting ip.
   Classless network is support Subnetting ip. It is also known as         CIDR (Classless interdomain Routing)



Now Configure By RIP-v2 Dynamic Routing

1. Diagram

First take router(2621-XM) and add port(WIC-2T) According to following  Diagram 






Go to first router in cli mode and type
          No
          Router>en
          Router#conf t
          Router(config)#int s0/0
          Router(config-if)#ip address 192.168.30.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#clock rate 64000
          Router(config-if)#exit
          Router(config)#int f0/0
   Router(config-if)#ip address 192.168.10.1 255.255.255.0
   Router(config-if)#no shut
          Router(config-if)#exit
        Router(config)#int f0/1
        Router(config-if)#ip address 172.16.1.1 255.255.255.0
        Router(config-if)#no shut
         Router(config-if)#exit

Go to second router in cli mode
          No
          Router>en
          Router#conf t
          Router(config)#int s0/0
          Router(config-if)#ip address 192.168.30.2 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
          Router(config)#int s0/1
          Router(config-if)#ip address 192.168.40.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#clock rate 64000
          Router(config-if)#exit
          Router(config)#int f0/0
          Router(config-if)#ip address 192.168.20.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
         Router(config)#int f0/1
         Router(config-if)#ip address 172.17.1.1 255.255.255.0
         Router(config-if)#no shut
         Router(config-if)#exit


Go to Third router in cli mode
          No
    Router>en
          Router#conf t
    Router(config)#int s0/0
          Router(config-if)#ip address 192.168.40.2 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
          Router(config)#int f0/0
          Router(config-if)#ip address 192.168.50.1 255.255.255.0
          Router(config-if)#no shut
          Router(config-if)#exit
         Router(config)#int f0/1
         Router(config-if)#ip address 172.18.1.1 255.255.255.0
         Router(config-if)#no shut
         Router(config-if)#exit


Step 2 Routing  

In First Router
First check network in (Router# Show ip route)
Then type
Router#conf t
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.10.0
Router(config-router)#network 192.168.30.0
Router(config-router)#network 172.16.1.1

In Second router
Router# Show ip route
Router#conf t
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.20.0
Router(config-router)#network 192.168.30.0
Router(config-router)#network 192.168.40.0
Router(config-router)#network 172.17.1.1

In Thrid router
Router# Show ip route
Router#conf t
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.40.0
Router(config-router)#network 192.168.50.0
Router(config-router)#network 172.18.1.1

To check Send Packet's Between Networks or ping IP 
go to first router and ping last router according to the diagram.
                    -----------------------------------END--------------------------------

No comments :

Post a Comment

Subscribe to: Post Comments ( Atom )

Contact Form

Name

Email *

Message *